鱼C论坛

 找回密码
 立即注册
查看: 2959|回复: 3

思科路由命令珍藏版

[复制链接]
发表于 2011-10-24 00:16:39 | 显示全部楼层 |阅读模式

马上注册,结交更多好友,享用更多功能^_^

您需要 登录 才可以下载或查看,没有账号?立即注册

x
这个是我以前搞路由交换的时间,总结的一些基本命令!都是最简单的了,有意搞网络的人看看吧,思科的命令!


路由器命令大全
  路由器命令
router> 用户模式
1:进入特权模式 enable
router > enable
router #
2:进入全局配置模式 configure terminal
router > enable
router #configure terminal
router (conf)#
3:交换机命名 hostname routera 以routerA为例
router > enable
router #configure terminal
router(conf)#hostname routerA
routera (conf)#
4:配置使能口令 enable password cisco 以cisco为例
router > enable
router #configure terminal
router(conf)#hostname routerA
routerA (conf)# enable password cisco
5:配置使能密码 enable secret ciscolab 以cicsolab为例
router > enable
router #configure terminal
router(conf)#hostname routerA
routerA (conf)# enable secret ciscolab
6:进入路由器某一端口 interface fastehernet 0/17 以17端口为例
router > enable
router #configure terminal
router(conf)#hostname routerA
routerA (conf)# interface fastehernet 0/17
routerA (conf-if)#
进入路由器的某一子端口 interface fastethernet 0/17.1 以17端口的1子端口为例
router > enable
router #configure terminal
router(conf)#hostname routerA
routerA (conf)# interface fastehernet 0/17.1
7:设置端口ip地址信息
router > enable
router #configure terminal
router(conf)#hostname routerA
routerA(conf)# interface fastehernet 0/17 以17端口为例
routerA (conf-if)#ip address 192.168.1.1 255.255.255.0 配置交换机端口ip和子网掩码
routerA (conf-if)#no shut 是配置处于运行中
routerA (conf-if)#exit
8:查看命令 show
router > enable
router # show version 察看系统中的所有版本信息
show interface vlan 1 查看交换机有关ip 协议的配置信息
show running-configure 查看交换机当前起作用的配置信息
show interface fastethernet 0/1 察看交换机1接口具体配置和统计信息
show mac-address-table 查看mac地址表
show mac-address-table aging-time 查看mac地址表自动老化时间
show controllers serial + 编号 查看串口类型
show ip router 查看路由器的路由表
9:cdp相关命令
router > enable
router # show cdp 查看设备的cdp全局配置信息
show cdp interface fastethernet 0/17 查看17端口的cdp配置信息
show cdp traffic 查看有关cdp包的统计信息
show cdp nerghbors 列出与设备相连的cisco设备
10:csico2600的密码恢复
重新启动路由器,在启动过程中按下win+break键,使路由器进入rom monitor
在提示符下输入命令修改配置寄存器的值,然后重新启动路由器
remmon1>confreg 0x2142
remmon2>reset
重新启动路由器后进入setup模式,选择“no”,退回到exec模式,此时路由器原有的配置仍然保存在startup-config中,为使路由器恢复密码后配置不变把startup-config中配置保存到running-config中,然后重新设置enable密码,并把配置寄存器改回0x2102:
router>enable
router#copy startup-config running-config
router#configure terminal
router(conf)#enable password cisco
router(conf)#config-register 0x2102
保存当前配置到startup-config , 重新启动路由器。
router #copy running-config startup-config
router #reload
11:路由器telnet远程登录设置:
router>en
router #configure terminal
router (conf)#hostname routerA
routerA (conf)#enable password cisco 以cisco为特权模式密码
routerA (conf)#interface fastethernet 0/1 以17端口为telnet远程登录端口
routerA (conf-if)#ip address 192.168.1.1 255.255.255.0
routerA (conf-if)#no shut
routerA (conf-if)#exit
routerA (conf)line vty 0 4 设置0-4 个用户可以telnet远程登陆
routerA (conf-line)#login
routerA (conf-line)#password edge 以edge为远程登录的用户密码
主机设置:
ip 192.168.1.2 主机的ip必须和交换机端口的地址在同一网络段
netmask 255.255.255.0
gate-way 192.168.1.1 网关地址是交换机端口地址
运行:
telnet 192.168.1.1
进入telnet远程登录界面
password : edge
routera>en
password: cisco
routera#
12:配置路由器的标识 banner $……………$
在全局配置的模式下利用“banner”命令可以配置路由器的提示信息,所有连接到路由器的终端都会收到。
router>en
router #configure terminal
router (conf)#hostname routerA
routerA(conf)#banner motd $This is aptech company’ router ! Please don’t change the configuration without permission!
$13:配置接口标识 description ………
接口标识用于区分路由器的各个接口。
router>en
router #configure terminal
router (conf)#hostname routerA
routerA(conf)#interface fastethernet 0/1 以0/1 接口为例
routerA(conf-if)# description this is a fast Ethernet port used to connecting the company’s intranet!
14:配置超时
超时适用于设置在多长时间没有对console进行配置,自动返回exec会话时间。默认为10分钟。
router>en
router #configure terminal
router (conf)#hostname routerA
routerA(conf)#line console 0
routerA(conf-if)#exec-timeout 0 0 第一个“0”代表分钟,第二个“0”代表秒
15:配置串口参数
两台路由器通过串口连接需要一个做为DTE,一个做为DCE。DCE设备要向DTE设备提供时钟频率和带宽。
DCE配置:
router>en
router #configure terminal
router (conf)#hostname routerA
routerA(conf)#interface serial 0/0
routerA(conf_if)#clock rate 64000 提供时钟频率为64000
routerA(conf_if)#bandwidth 64 提供带宽为64
DTE配置:路由器串口配置ip地址
router>en
router #configure terminal
router (conf)#hostname routerB
routerB(conf)#interface serial 0/0
routerB(conf_if)#ip address 192.168.1.1 255.255.255.0
16:静态路由的配置
配置路由器A的主机名和接口参数
router>enable
router#configure terminal
router(conf)#hostname routerA
routerA(conf)#interface fastethernet 0/1 路由器A的1端口为两路由器的连接端口
routerA(conf-if)#ip address 192.168.2.1 255.255.255.0
routerA(conf-if)#no shutdown
routerA(conf-if)#exit
routerA(conf)# interface fastethernet 0/0 路由器A的0端口为与主机的连接端口
routerA(conf-if)#ip address 192.168.1.2 255.255.255.0
routerA(conf-if)#no shutdown
主机A的ip地址为 192.168.1.1
255.255.255.0
192.168.1.2
配置路由器B的主机名和接口参数
router>enable
router#configure terminal
router(conf)#hostname routerB
routerB(conf)#interface fastethernet 0/0 路由器B的0端口为两路由器的连接端口
routerB(conf-if)#ip address 192.168.2.2 255.255.255.0
routerB(conf-if)#no shutdown
routerB (conf-if)#exit
routerB(conf)# interface fastethernet 0/1 路由器B的1端口为与主机的连接端口
routerB(conf-if)#ip address 192.168.3.1 255.255.255.0
主机B的ip地址为 192.168.3.2
255.255.255.0
192.168.3.1
配置路由器A的静态路由表
routerA(conf)#ip router 192.168.3.0 255.255.255.0 192.168.2.2
配置路由器B的静态路由表
routerA(conf)#ip router 192.168.1.0 255.255.255.0 192.168.2.1
在routerA和routerB上配置默认路由
routerA(conf)#ip route 0.0.0.0 0.0.0.0 192.168.2.2
routerA(conf)#ip classless
routerB(conf)#ip route 0.0.0.0 0.0.0.0 192.168.2.1
routerB(conf)#ip classless
在routerA和routerB上配置动态路由(RIP)
routerA(conf)#router rip
routerA(conf)#network 192.168.1.0
routerA(conf)#network 192.168.2.0
routerB(conf)# router rip
routerB(conf)#network 192.168.2.0
routerB(conf)#network 192.168.3.0

评分

参与人数 1鱼币 +8 收起 理由
乐め乐 + 8

查看全部评分

想知道小甲鱼最近在做啥?请访问 -> ilovefishc.com
发表于 2011-10-24 00:52:35 | 显示全部楼层
在学校考试网络技术时 就用的到这个。。可惜命令现在都忘了
:loveliness:
想知道小甲鱼最近在做啥?请访问 -> ilovefishc.com
发表于 2011-10-24 22:25:17 | 显示全部楼层
不错不错,值得收藏
想知道小甲鱼最近在做啥?请访问 -> ilovefishc.com
发表于 2011-10-25 22:13:14 | 显示全部楼层
不错不错,值得收藏
想知道小甲鱼最近在做啥?请访问 -> ilovefishc.com
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

小黑屋|手机版|Archiver|鱼C工作室 ( 粤ICP备18085999号-1 | 粤公网安备 44051102000585号)

GMT+8, 2024-3-29 12:47

Powered by Discuz! X3.4

© 2001-2023 Discuz! Team.

快速回复 返回顶部 返回列表